10G X2 ER

10G X2 ERX2 10GBASE-ER 1550nm, 40km Reach (PN: S2-5592-ERC)Features ●  Compatible with X2 MSA Rev2.0b ●  Support of IEEE 802.3ae 10GBASE-ER at 10.3125Gbps ●  Transmission Distance up to 40Km(SMF) ●  SC Receptacle 1550nm Cooled EA-DFB Laser ●  SC Duplex Optical Connector ●  Hot Pluggable 70-PIN Connector with XAUI Electrical Interface ●  Management and control via MDIO 2-wire interface ●  Power Supply : +5V, +3.3V, APS(+1.2V) ●  Diagnostic Optics Monitoring ●  Temperature Range: 0~ 70 °C ●  ROHS CompatibleApplications ●  10GE Ethernet switches and routers ●  10GE Core-routers ●  10GE Storage ●  Other 10Gbps Ethernet Transmission System Transmitter CharacteristicsParameter Symbol Min. Typ. Max. Unit Note Operating Range10KmOperating Date Rate10.3125Gb/sOptical Transmit PowerPo-1.0+2.0dBmInput Centre Wavelengthλ153015501570nmSMSR.SWSR30dBExtinction RatioER9.0Optical Modulation AmplitudeOMA500µWTransmitter and Dispersion      PenaltyTDP3.2dBReceiver Characteristics Parameter Symbol Min. Typ. Max. Unit Note Operating Date Rate10.3125Gb/sOverloadPo0.5dBmSensitivity in 10.3G(OMA)OMA0-14.1dBm1Stressed Sensitivity in 10.3G(OMA)OMAst-11.3dBm1Note1. Measured at 10.3125 Gb/s, Non-framed PRBS2^31-1, NRZPin Descriptions  PIN NO Name Dir Logic Function Notes 1GNDElectrical Ground2GNDElectrical Ground3GNDElectrical Ground45.0VPower53.3VPower63.3VPower7APSAdaptive Power Supply8APSAdaptive Power Supply9LASIO1.2V CMOS Open Drainlink Alarm Status Interrupt, low active, Open Drain Output A pull-up resistor with 10-22KΩ to 1,2V is expected. Logic High: Normal Operation Logic Low: link Alarm is indicated10ResetI1.2V CMOS  Open DrainLow active Reset Input 10K Ω pull-up on Transceiver   Logic high = Normal Operation Logic Low = Reset asserted11VEND SPECIFICVendor Specific Pin,. leave unconnected12TX ON/OFFI1.2V CMOS      Open DrainHigh active Transmitter Enable Input 10KΩ pull-up on Transceiver   Logic high = Transmitter active (normal Operation) And Register Bit 1.9.0 set to low as well Logic Low = shut down of Transmitter13RESERVEDRESERVED14MOD DETECTO1k Ω to Ground On Transceiver15VEND SPECIFICVendor Specific Pin,. leave unconnected16VEND SPECIFICVendor Specific Pin,. leave unconnected17MDIOI/O1.2V CMOSManagement Data I/O. Requires external 10-22 kΩ pull-up to 1.2 V on host.18MDCI1.2V CMOSManagement Clock Input19PRTAD4IPort Address Bit 4(LOW=0)20PRTAD3IPort Address Bit 3(LOW=0)21PRTAD2IPort Address Bit 2(LOW=0)22PRTAD1IPort Address Bit 1(LOW=0)23PRTAD0IPort Address Bit 0(LOW=0)24VEND SPECIFICVendor Specific Pin,. leave unconnected25APS SETIFeedback Input for APS, Input of APS Setting Resistor26RESERVEDRESERVED27APS SENSEOAPS Sense Output for APS Control Circuit28APSAdaptive Power Supply29APSAdaptive Power Supply303.3VPower313.3VPower325.0VPower33GNDElectrical Ground34GNDElectrical Ground35GNDElectrical GroundPIN NO Name Dir Logic Function Notes 36GNDElectrical Ground37GNDElectrical Ground38RESERVEDRESERVED39RESERVEDRESERVED40GNDElectrical Ground41RX LANE 0+Module XAUI Output Lane 0+42RX LANE 0-Module XAUI Output Lane 0-43GNDElectrical Ground44RX LANE 1+Module XAUI Output Lane 1+45RX LANE 1-Module XAUI Output Lane 1-46GNDElectrical Ground47RX LANE 2+Module XAUI Output Lane 2+48RX LANE 2-Module XAUI Output Lane 2-49GNDElectrical Ground50RX LANE 3+Module XAUI Output Lane 2+51RX LANE 3-Module XAUI Output Lane 2-52GNDElectrical Ground53GNDElectrical Ground54GNDElectrical Ground55RX LANE 0+Module XAUI Output Lane 0+56RX LANE 0-Module XAUI Output Lane 0-57GNDElectrical Ground58TX LANE 1+Module XAUI Output Lane 1+59TX LANE 1-Module XAUI Output Lane 1-60GNDElectrical Ground61TX LANE 2+Module XAUI Output Lane 2+62TX LANE 2-Module XAUI Output Lane 2-63GNDElectrical Ground64TX LANE 3+Module XAUI Output Lane 2+65TX LANE 3-Module XAUI Output Lane 2-66GNDElectrical Ground67RESERVEDRESERVED68RESERVEDRESERVED69GNDElectrical Ground70GNDElectrical Ground Ordering information for 10G X2 ER Part Number Product Description S2-5592-ERCX2 10.3125Gbps 1550nm 40Km, 0°C ~ +70°C